Temel bilgiler.
Anahtar Sayısı
Tek Kontrol Anahtarı
Kullanım
Kontrol Anahtarı
Patlamaya dayanıklı Tip
Patlamaya dayanıklı değil
Algılama Yöntemi
Retro Yansıtıcı Mod
Working Viscosity
<1× 10-3m2/S
Ambient Temperature
-25o C~+55o C
Medium Temperature
-25o C~+80o C
Mount Position
Pressure Connection Virtically Downward
Protection Class of Enclosure
IP54
Anti-Vibration
Max: 100m/S2
Repeatablity Error
≤ 2.5%
Electric Rating
AC 220V 6A(Resistance)
Ürün Açıklaması
The Sensor of Switches utilize Diaphragm-Piston Conbination, 500/18D Switches use Diaphragm Sensor can be suitable for neutral gas, lubricating oil, light fuel ect. Fluid medium. 505/18D Switches use no-leak piston sensor, can be fit for lubricating oil, light fuel such neutral lube medium. The Set Point is adjustable, and its adjustable range is from 0.5Mpa to 40Mpa.
(If special requirments is needed, please refer to our Application Handbook )
Features
Ultra-compact designed control system, guarantee the switching frequence to be 100 times/min., and good perofrmance of vibration resistance.
Remarks: In the practice, even the temporal peak value of pressure, should no exceed the Max. Allowable Pressure.
I-means the connection is Female Screw,
P-means the connection is Flange
The Adjustment of Set Point
[Example] Choose Order No. 0882200 Switch, a contact signal is required to be generated when pressure falls to 8Mpa(The Decreasing Set Point), see steps as following:
To screw the Switch into connection of Oil Pressure Checkout Test Set(if the connection is Flange, then choose the Flange connection of the Checkout Test Set). Exert pressure on it for 2 minutes simulate its practical working situation, thereafter to make the setting.
Link the Out-put lead with Multimeter.
Screw-off the screws on the housing.
Add the pressure to 8Mpa, this value can be read from the standarded pressure gauge.
Loose the locknut, use socket screwwrench (Φ 5mm), clockwise rotate the Set-point Adjusting Bolt, to make the Set-Point become bigger, until it switches at 15Mpa.
Tighten the locknut, vering the testing pressure to make it change up and down arround 8Mpa, check if the Switch switches at 8Mpa when pressure falls, this value is the Decreasing Set Point need to be set, the correspondent Increasing Set Point to be 0.8Mpa plus 2.3Mpa(The Dead Band), namely 10.3Mpa(approximately).
Selection and Installation
*The Set Point must be within the aAdjustable Range, Dead Band is expressed as Typical at mid-range. Normally it is the 20% to80% of the Ajustable Range.
*If the switches are outdoor application, sufficient protections are necessary, for the severe variation of the ambient temperature, radiation of the sunlight, permeation of the corrosive gas or water, will influence the life of the switches.
*During the process of installation or disassembly, a spanner MUST be used to clip and tighten the sensor, absolutely avoid the countermovent between the sensor and housing of the switches(please refer to the drawings)
*Regarding those controlled fluid medium with peak value of pressure and plusation pressure, a damper can be installed at the connection, to eliminate negative influence
*On-Off current should not be greater than the Rating.
*If the connection of the Switches are threaded type, the depth for the pipe to go in should not exceed 12mm.
*During the process of installation or disassembly, a spanner MUST be used to clip and tighten the sensor, absolutely avoid the countermovent between the sensor and pipe.
Set Point adjustable range Mpa | Dead Band No Greater Than | Max. Allowable pressure* Mpa | Material of sensor | Process Connection Type | Connection(F) | Weight Kg | Order Content No. |
Lower limit of Set Point Range Mpa | Upper limit of Set Point Range Mpa | Shell | Sealing Ring | Piston |
500/18D Diaphragm Type Pressure Switch |
-0.1^0 | 0.015 | 0.02 | 8 | Al | Nitrile Rubber | Steel | I | G1/4" | 0.2 | 0880100 |
-0.1^0 | 0.015 | 0.02 | P | | 0881100 |
0.02^0.2 | 0.02 | 0.04 | I | G1/4" | 0880200 |
0.02^0.2 | 0.02 | 0.04 | P | | 0881200 |
0.05^0.8 | 0.04 | 0.13 | I | G1/4" | 0880300 |
0.05^0.8 | 0.04 | 0.13 | P | | 0881300 |
0.1^1.6 | 0.06 | 0.24 | I | G1/4" | 0880400 |
0.1^1.6 | 0.06 | 0.24 | P | | 0881400 |
505/18D Piston Type Pressure Switch |
0.5^7 | 0.8 | 2 | 40 | Al | Nitrile Rubber | Steel | I | G1/4" | 0.2 | 0882100 |
0.5^7 | 0.8 | 2 | P | | 0883100 |
1^16 | 1.2 | 3.5 | I | G1/4" | 0882200 |
1^16 | 1.2 | 3.5 | P | | 0883200 |
2.5^25 | 1.5 | 4 | I | G1/4" | 0882300 |
2.5^25 | 1.5 | 4 | P | | 0883300 |
4^40 | 1.8 | 4.5 | 60 | I | G1/4" | 0882400 |
4^40 | 1.8 | 4.5 | 60 | P | | 0883400 |
Adres:
Guohe Industrial Park, Menghe Town, Xinbei District, Changzhou, Jiangsu, China
İşletme Türü:
Üretici/Fabrika
İşletme Aralığı:
Araçlar ve Sayaçlar, Elektrik ve Elektronik, Endüstriyel Ekipmanlar ve Bileşenleri
Şirket Tanıtımı:
Changzhou Tianli Denetleyici İmalat Şirketi, Ltd. ISO9001:2000′de yüksek teknoloji kanıtlamalıdır. Şirket, üretim ürünlerinde profesyoneldir. Bu ürünler şunları içerir: Basınç/Diferansiyel Vericiler, basınç anahtarlarını gösteren, İki seviyeli basınç Anahtarları, Paslanmaz basınç Ölçerleri, Gölgesiz basınç Ölçerler, Vb. Petrol ve gaz, kimyasal, petrokimya, kimyasal fiber, enerji endüstrisi, Metalürji, tıp, ışık endüstrisi, telekomünikasyon sektörleri ve yeniden nakliye ekipmanlarının kendi kendini Kontrol ve Kontrol Merkezi, proses uygulamasında kendi kendini Alarm özelliği ve koruma. "Tianxiang" markamız, müşteriler tarafından yüksek doğruluk, yüksek kalite, güvenilirlik ve değişken özellikler olarak tanınır.
Şirket 1984 yılında kurulduğundan beri Tianli, sürekli teknik yenilikler ve yüksek kaliteli ürünler üretmeye kendini adamıştır. Bu arada tipik ürünlerimiz de normalde gereksinimlerinizi karşılayabilir. Özelleştirilmiş tasarım yapabiliyoruz. Müşteri odaklı bir hizmet felsefesi ele alıyoruz. Müşteri gereksinimlerine yanıt vermek için hizmet ve ürün stratejilerimizi sürekli olarak geliştirmek için işimizi geliştiriyoruz.
Dünyanın her yerindeki kullanıcıları ve arkadaşlarımızı birlikte çalıştırmayı umuyoruz, lütfen bizi arayabilir veya bize e-posta gönderebilirsiniz.