Y6-51 boiler-induced draft fan
Y6-51 boiler-induced draft fan is suitable for the air supply and induction system of 2~670t/h steam boilers in power plants, and also meets the requirements of the performance parameters of the high-pressure head of the fluidized bed furnace. This series of fans can also be used in dust removal, mine ventilation, and general ventilation systems.
The Y6-51 boiler-induced draft fan transports flue gas or gas containing impurity particles. When the impurity concentration is less than 200mg/m3, it can be used for more than 4 years. It can also be used if it contains large impurities, but the service life will be shortened. The operating temperature of the induced draft fan shall not exceed 250°C.
The Y6-51 boiler-induced draft fan can be made of FRP or stainless steel for the transportation of a certain concentration of corrosive gas.
For the transportation of flammable and explosive gases, it is equipped with cast aluminum impellers and explosion-proof motors and can be made into explosion-proof fans.
For gas transmission greater than 80° and less than 250°, water-bearing housings can be used, made of ordinary steel plates, and stainless steel is recommended for gas transmission greater than 250°.
As the temperature of the boiler-induced fan increases, the pressure of the fan will change to a certain extent, and the power of the equipped motor will also change. Please consult the manufacturer for details.
Y6-51 boiler-induced draft fan is based on the principle of converting kinetic energy into potential energy, using the high-speed rotating impeller to accelerate the gas, then decelerate, change the flow direction, and convert kinetic energy into potential energy (pressure). In a single-stage centrifugal fan, the gas enters the impeller from the axial direction, changes to the radial direction when passing through the impeller, and then enters the diffuser. In a diffuser, the gas changes direction, and the cross-sectional area of the duct increases to decelerate the gas flow. This deceleration converts kinetic energy into pressure energy. Pressure changes mainly occur in the impeller, followed by the diffusion process. In a multi-stage centrifugal fan, a reflux device is used to direct the airflow to the next impeller, resulting in a higher pressure [1].
The principle of the Y6-51 boiler-induced draft fan is basically the same as that of the turbine compressor. It is because the gas flow rate is low and the pressure changes little. Generally, it is not necessary to consider the change of the gas-specific volume, that is, the gas is treated as an incompressible fluid.
Centrifugal fans can be made into two types right-handed and left-handed. Viewed from the side of the motor: the impeller rotates clockwise, known as a right-rotating fan; the impeller rotates counterclockwise, known as a left-rotating fan.
Y6-51 boiler-induced draft fan form
1) Blower fan and induced draft fan are made into single suction form. Machine number №8~29.5
2) Each fan can be made into two forms left rotation or right rotation.
3) The position of the air outlet of the fan is represented by the same outlet angle as the casing.
4) The transmission mode of the fan is D type (that is, the cantilever structure), and the motor and the fan are connected by elastic couplings, which are directly connected to the drive.
5) An example of the full name of the product is as follows:
G6-51№18D right 90 degrees
Y6-51№18D left 0 degrees
Among them: G and Y represent the boiler supply fan and the boiler-induced draft fan respectively, 5 represents the pressure coefficient of the efficiency point 10 times rounded up, 51 represents the specific speed, 1 represents the secondary design, and №18 represents the impeller diameter of 1800mm.
Composition of Y6-51 boiler-induced draft fan
The fan is composed of a casing, an air inlet, an impeller, an overall support, a transmission part, an adjusting door (according to customer needs), and a motor. The fan has been strictly tested before leaving the factory, and the amplitude has reached the national standard. The overall support of fans above 18# is purchased according to customer needs. (usually with a concrete foundation)
Chassis: It is made of steel plate, which is solid and reliable. It can be divided into integral type and semi-open type. The semi-open type is easy to overhaul. The fan below 14# is mostly integral type, and the fan above 14# is mostly semi-open type
Impeller: It is composed of 12 twisted blades, a curved front disc, and a flat rear disc welded. Static balance and dynamic balance should be done to ensure that the fan rotates smoothly and has good performance. The leaf form is
Transmission part: It consists of the main shaft, bearing box, rolling bearing, and pulley (or coupling). The transmission is equipped with a water-cooling device to cool down the bearing and prolong the service life.
Air inlet: Welded by steel plates into a tapered shape, forming a convergent streamlined overall structure, installed on the side of the fan and the cross-section of the axial line is a curved shape so that the gas can enter the impeller smoothly with less loss.
Adjusting door: Installed in front of the air inlet, the air volume can be adjusted under the condition that the fan speed (pressure) is constant.
Overall bracket: welded by channel steel and steel plate, the whole is firm, stable, and durable.
Motor: It adopts a large manufacturer, a full copper core motor, and generally defaults to a Class 3 energy efficiency motor. Frequency conversion motors, explosion-proof motors, and energy-efficient motors above level 2 can also be customized according to customer needs
Structural Features of Y6-51 Boiler-Induced Fan
1. The fan adopts advanced proprietary technology achievements such as a high-strength wear-resistant impeller, oil-leakage-proof bearing box, and articulated axial adjustment door.
2. The range of high-efficiency working conditions is wide, and the fan numbers are arranged densely, making it easy to select high-efficiency working conditions.
3. Adopt an adjustable air inlet. Adjust the axial and radial clearances between the air inlet and the impeller when the fan is installed.
4. High-strength wear-resistant impeller. The impeller adopts backward single-plate blades, which reduces the impact of airflow, has good stability, and the motor is not easy to be overloaded, which greatly prolongs the service life of the fan. This type of fan has high-pressure coefficient, low peripheral speed, and low noise, so it has good practicability.
5. Leakproof bearing box. The lapped oil throwing ring is used to throw the oil brought by the high-speed rotating bearing to the inner wall of the bearing box and flow back to the oil pool: the semi-open aluminum oil seal can not only facilitate maintenance and prevent friction accidents but also increase the resistance along the axial direction to move the part The thin oil is intercepted and returned to the oil pool; the outer pressure packing blocks a small amount of thin oil; the upper part of the bearing box is equipped with a vent plug to reduce the slight positive pressure in the bearing box to ensure no oil leakage and good dustproof performance.
6. Articulated axial adjustment door. The fulcrum of the guide vane of the adjustment door and the adjustment rod are equipped with joint bearings, and there is no "dead" point in the operation and adjustment process, so the adjustment is flexible, labor-saving, safe and reliable, and ensures that the actuator is not overloaded.
7. The fan is an integral or split assembly. The transmission group, coupling cover, and motor of this series of fans below 16D are assembled on a complete base before leaving the factory; the casing, air inlet, and adjusting door are another component, and the small type fans are assembled into two components when leaving the factory. The number is disassembled and assembled into multiple components for transportation and installation.
8. The fan is a cantilever structure, which is convenient to arrange, and the motor is directly connected to the drive, which can transmit torque evenly, reduce vibration and make the fan run reliably.
9. The fan is easy to install and overhaul. The fan has two complete base casings and a transmission group. The casing has a central or vertical split surface, which is particularly convenient for disassembly and assembly. The rotor can be lifted out vertically, and it can also be disassembled axially when only replacing the impeller.
More about this source texture text is required for additional translation information
Send feedback
Side panels
Product Specification:
| Model No |
G6-51 8D-29.5D |
| Use |
High-temperature smoke exhaust Fan for Fire Protection |
| Voltage (V) |
380V/400V/415V/440V/450V/660V/1140V |
| Color |
Blue/Red/White/Gray/Yellow/Customized |
| Application Industries |
Widely used for fire fighting, kitchen exhaust, restaurant, smelting, coking, chemical, industries, etc |
| Size |
Have many sizes, Can provide according to customer's requirement size |
| Brand Name |
Zhi Feng |
| Power |
15~400KW |
| Rotating Speed |
1450~480rpm |
| Total Pressure |
2745~5893Pa |
| Airflow |
11000~439000m3/h |
| Temperature |
400ºC |
| Package |
Wooden Box/Steel frame |
| Material |
SS304,SS316 and Q235 |
| Frequency |
50Hz/60Hz |
| Impeller Type |
Backward/Forward/Radial Blade |
| After-Sales Service |
Online support |
| Efficiency(%) |
Over 85% |
| Exported to |
All Countries |
| Warranty |
18 Months |
Product Parameters
Standard Blower Induced Draft Fan Manufacturers (Y6-51) Performance Table
| machine model number |
Rotating Speed
R/min |
Total
Pressure |
Airflow
M³/h |
Electric motor |
| model |
power |
| G6-51 8D-29.5D |
1450~480rpm |
2745~5893Pa |
11000~439000m3/h |
Y160L-4/380V~Y200-8/1730 |
15~400KW |
Detailed Photos
Certifications
Packaging & Shipping
1) The equipment is equipped with a number of signs such as a product nameplate, rotation direction sign, wind direction sign, grounding sign, lifting sign, safety warnings, and so on.
2) Product nameplate mainly includes the contents of the equipment: main technical parameters (flow, pressure, motor power, Revolutions Per Minute), product number, manufacturing date, and so on, which is convenient for users to check at any time
3) Small equipment adopts the type of export wood packaging and large equipment, and the steel frame transports large cargo transportation.
4) All equipment is waterproof and rainproof.
5), Random files are placed in a moisture-proof packaging bag and are transported together with the equipment.
6) Appearance of all packaging is waterproof, moisture-proof, clean, and durable.
7) The appearance of the packaging is marked with product mark, hoisting mark, weight, etc.
8) After the equipment is packaged, they are loaded into a container or frame and transported by car to the port (train station).
9) The equipment adopts a split structure, and the outer dimensions of the packaging of the largest goods fully meet the relevant requirements of road transport and the sea.
Company Profile
Zibo Hengding Fan Co., Ltd. Is located in Industrial Park, Beijiao Town, Zhoucun District, Zibo City, Shandong Province, China. The company covers an area of 12,000 square meters and a construction area of 8,000 square meters. The company has total assets of 27 million RMB and 186 employees, 46 engineers, and technicians. It has passed ISO9001 quality management system certification and has maintained long-term technical cooperation relationships with many colleges and universities, such as Xi'an Jiaotong University, Tianjin Nankai University, and so on. Now, it has developed into a modern ventilation equipment manufacturing enterprise with first-class testing and producing equipment, high-quality and excellent production molds, strong scientific research and development strength, a strict quality management system, and gradually perfected development. The company has 15 years of production experience, with an annual output of 5,000 sets of ventilators.
With the market demand as the development direction, the company has always adhered to independent R&D and continuous innovation. Now it has developed into a modern environmental protection, and ventilation equipment enterprise, which mainly consists of mine fans, coal mine ventilators, and centrifugal ventilators. There are more than 50 series of ventilator products with more than 600 specification models, widely used in many industries, such as mines, coal mines, oil fields, chemical industry, kilns, metallurgy, boiler, textile and building materials, etc. The company's products are sold continuously with reliability in 29 provinces, cities, and autonomous regions of China, as well as Vietnam, Indonesia, Russia, Serbia, Pakistan, Kazakhstan, Tajikistan, Iraq, Saudi Arabia, and other countries.
As a manufacturer specializing in ventilation equipment, it is committed to providing superior quality products with advanced technology to customers. We will continue to make new contributions to the development of the ventilator industry based on the management philosophy of "Peng Fei''!
As a manufacturer specializing in ventilation equipment, it is committed to providing superior quality products with advanced technology to customers. We will continue to make new contributions to the development of the ventilator industry based on the management philosophy of "responsibility, teamwork, efficiency and innovation" and the enterprise spirit of "Faith determines height and quality creates brilliance".
We are willing to cooperate with all the new and old customers to create brilliance with first-class quality, reasonable prices, and a perfect service system.
General Manager Wang Baiqing warmly welcomes friends from all walks of life to visit our company for inspection and guidance.
Our Advantages
Strict quality standards, precision machining, and other spare parts and design maintain product stability, strictly select product parts suppliers, and perfect after-sales service system to allow customers to enjoy a new experience
Our company has introduced the latest research results of the Chinese Academy of Sciences, C4-II ternary flow wing twisted blades, which have high aerodynamic efficiency.
The surface of the ventilator impeller blade is sprayed with advanced super-resistant (CN) metal material to form a wear-resistant, anti-corrosion protection layer on the surface of the blade. The wear resistance of the blade surface is 10 to 50 times higher than that of the ordinary carbon steel material, thereby greatly prolonging the service life of the blade.
After we have absorbed the advantages of many domestic blade structures, based on the optimal control theory of concentrated parameters and distributed parameters, adopting the advanced ternary flow theory of impeller machinery and perfect CAD design technology, through multi-parameter control by blade bending amount, this blade is a high-performance fan blade. It ensures that the ventilator is operating in a wide and efficient area on the premise of meeting the wind volume and wind pressure.
Our company adopts computer simulation calculation and quasi-ternary flow theory, we correct the blade shape and calculate coordinate parameters of its shape, then make the core mold and the external pressure mold of the blade, and the blades are formed by hot pressing. According to a large number of experiments, the tilting blade has a larger lift-to-drag ratio than the original organic blade type and is the best choice for the airfoil blade.
The blades are welded with high-strength carbon steel material. The petiole is treated with high-quality carbon steel. So that the blade maintains the strength and rigidity of the steel blade when ensuring the corrosion resistance and wear resistance of the blade. Moreover, it effectively protects the blade from corrosion resistance and wear resistance in a humid air environment, and improves the operating life of the ventilator.
The surface of the blade is coated with a super-resistant (CN) metal material coating, which not only maintains the strength and rigidity of the high-quality carbon steel blade, but also effectively protects the blade from corrosion resistance and wear resistance in a humid air environment, and improves the operating life of the ventilator.
The petiole is forged and made of high-quality medium carbon steel, and the tempering heat treatment is performed. The root has enough transition arc to eliminate stress concentration, through reasonable and correct force analysis and calculation, the strength, and safety factor of the most dangerous section of the blade root is more than 6 times. And carry out 100% X-ray non-destructive testing for welding seams of the blade root section and the blade, and all the defects were eliminated. Therefore, the impeller has a high degree of operational safety. Since the supply of the ventilator produced by our company, there has never been an accident of the petiole breaking and flying blades.
The impeller hub is made of high-quality steel and then tempered to process heat treatment. The surface of the hub is processed into a spherical shape, the petiole hole is placed at the thickest part of the center of the rim, which reduces the friction loss of the wind flow and ensures that the force-bearing section of the hub has sufficient tensile strength and rigidity. The welded joints of the hub all adopt groove welding and carry out 100% X-ray non-destructive testing for welding seam, which ensures the safe operation of the impeller.
After the blade is formed, first sandblasting is performed to remove dirt on the surface of the blade such as welding slag and oxide layer, to show the original color of the metal; Then, using the latest international inverter pulse arc power supply and high-speed arc spray gun to paint the super-resistant (CN) metal material on the surface of the blade, to form a wear-resistant anti-corrosion protection layer on the surface of the blade. Compared with the traditional arc spraying equipment and spraying process, the coating is denser, the ultra-resistant (CN) metal material has higher bonding strength with the blade's basic body, and the service life is longer.
Quality assurance measures:
In long-term production management, our company has formed a set of standardized process control measures and control points, which can provide users with high-quality products in all directions. Our company has a good reputation and is an enterprise that users can absolutely trust.
Our company has obtained the IS09001 certification from the International Organization for Standardization (see Enterprise Qualification Materials for details). We strictly standardize the operation process and control points of product manufacturing
After Sales Service
When the equipment of the buyer is installed, our company is responsible for on-site installation guidance, personnel training and commissioning of test-drive, The separately purchased fan accessories can be used for telephone connection guidance and debugging
Our company guarantees that the structural safety, aerodynamic performance, running noise, and appearance, quality of the supplied ventiators can be checked and accepted by relevant departments.
The buyer has the right to carry out irregular inspections on the whole machine equipment manufactured by our company to ensure provide convenience for the buyer's supervisory personnel;
Within the specified warranty period, any damage and malfunction caused by defects in product design, process or materials shall be the responsibility of our company. Our company guarantees to reply within 4 hours after receiving the buyer's notice, arriving to solve the problem within 48 hours. We will follow the principle that service work does not stop if the problem is not solved. The buyer may retain the claim for damages caused by manufacturing quality problems;
The quality assurance period for the supplied ventilator equipment, except for special provisions, is 12 months from the final acceptance of the ventilator; The warranty period for the individual parts of the fan is 6 months.
Before the expiration of the warranty period, if a problem with ventilator equipment occurs due to the manufacturing quality of our company, our company is responsible for free repair and replacement; if the problem is caused by the buyer, our company will also repair and replace it in time, and only charge its cost. ;
If out of our warranty period, our company also provides spare parts to the buyer at the most favorable price, guarantees to provide technical services for the equipment sold timely and with high quality, and the after-sales technical service is free for life, guarantees to arrive at the buyer's site for repair and technical guidance
FAQ
Q. What information should I provide when inquiring?
A: Fan name/model, KW, Air pressure, Flow rate Air Volume, and temperature
Q. What is your warranty?
A. Our warranty is 18 months after receiving the fans. During the warranty period, replace the damaged parts free of charge. Out warranty period, to provide timely, high-quality technical services and price concessions spare parts to ensure.
continuous safe and high-quality equipment operation.
Q. How does your factory control product quality?
A.We have a quality inspection department. All fans are running more than 3 hours before delivery to test the quality. If there is a quality problem, we will produce a new one.
Q. What are your terms of payment?
A. TT 40% AS THE ADVANCE PAYMENT AND TT 60% AFTER INSPECTION BEFORE SHIPPING.
B. 100% IRREVOCABLE L/C AT STGHT.
Q. What products do you produce?
A. Centrifugal fan, tunnel fan, axial fan, jet fan, mining fan, exhaust fan,anti-corrosion blower, high-pressure blower, explosion proof fan, etc, welcome to contact us to learn more details.
Q. Where is your factory? Can I visit your factory?
A. Zibo Hengding Fan Co., Ltd. Is located in Industrial Park, Beijiao Town, Zhoucun District, Zibo City, Shandong Province, China.
Q. How long will it take to ship after the order?
A. 10-15 Days if you need it urgently, we can discuss it for shorting time.
Q. Is the product customizable?
A. Various types can be customizable.
Denetlenen Tedarikçi 
